Hensel-Visit Certo 200 User Manual Download Page 2

Page: 2 / 56

Contents

Information about this manual and about the manufacturer ................... 5

Keeping this manual on hand .................................................................. 5

Design features in the text ...................................................................... 5

Design features in the figures .................................................................. 6

Manufacturer’s address ........................................................................... 7

Safety ..................................................................................................... 8

Intended use ............................................................................................ 8

Fundamental safety information ............................................................. 8

Prevention of equipment damage and malfunctions ............................ 10

Design features of warning notices ....................................................... 11

Design features of equipment or property damage information .......... 11

Warning and information sign ............................................................... 12

Description ........................................................................................... 13

Overview of scope of delivery ............................................................... 13

Overview of device ................................................................................ 14

Overview of swivel head ........................................................................ 15

Overview of controls ............................................................................. 16

Task and function .................................................................................. 18

Type plate .............................................................................................. 19

Technical data ........................................................................................ 20

Unpacking the device and checking the scope of delivery ...................... 22

Commissioning the device ..................................................................... 23

Mounting and removing components of the device ............................... 24

Removing and installing the transport cap ............................................ 24

Installing and removing the flash tube with protection glass................ 26

Installing and removing the illuminant of the model light .................... 27

Mounting the light shaping tool on/removing it from the device ......... 29

Connecting and disconnecting the mains cable .................................... 31

Summary of Contents for Certo 200

























































Search results

Summary of Contents for Certo 200

Reviews:

Related manuals for Certo 200

Brands by name

Popular brands

Hensel-Visit Certo 200, User Manual

Search results

Summary of Contents for Certo 200

Reviews:

Related manuals for Certo 200

Brands by name

Popular brands