Hensel-Visit Certo 200 User Manual Download Page 17 | Manualshive

Page: 17 / 56

background image

Description

17

No.

Designation

9

Sync socket

10

RF CH: Switch radio channels on and off

11

LAMP: Activating and deactivating the model light in “Full” and “Prop”
modes

12

AUDIO: Signal tone for activation and deactivation of flash readiness

13

SYNC: Activation and deactivation of photo cell and radio receiver

LED displays are located next to the buttons on the display. They light up
when the buttons are activated.

«
...
15
16
17
18
19
...
»

Summary of Contents for Certo 200

























































Reviews:

No comments

Related manuals for Certo 200

Brand: RAB Lighting Pages: 2

Brand: lap Pages: 2

Brand: Home Accents Holiday Pages: 2

Brand: Eye Lighting Pages: 2

Brand: leadsun Pages: 9

Brand: Quoizel Pages: 2

Brand: Hülsta Pages: 6

Brand: Squareled Pages: 15

Brand: IKEA Pages: 20

Brand: Ecco Pages: 3

Brand: Lighthouse Pages: 2

Brand: DPM Pages: 8

Brand: Bandini Industrie Pages: 22

Brand: Leuze Pages: 37

Brand: GE Pages: 4

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands