manualshive.com logo in svg

Hemisphere GPS V102 G, User Manual

Share
Download
Hemisphere GPS V102 G User Manual Download Page 41

36

Chapter 3: Operation

Common Commands and Messages

Note:

 When selecting your baud rate and message types, use the following 

calculation to determine your baud rate for your required data throughput.

Messages * Message output rate * Message length (bytes) * bits in byte
Ex: 5 * 20Hz * 40 bytes * 10 = 40,000 bits/sec

For information on message output rates refer to GPS Technical Reference 
available from the Hemisphere GPS website at 

www.hemispheregps.com

.

Table 3-2 below through Table 3-4 provide brief descriptions of common 
commands and messages for the V102. Refer to the Hemisphere GPS 
Technical Reference for more detailed information.

Table 3-2: Commands

Command

Description

$JAGE

Specify maximum DGPS (COAST) correction age (6 to 8100 
seconds)

$JAPP

Query or specify receiver application firmware

$JASC

Specify ASCII messages to output to specific ports (see ASCII 
messages in Table 3-3)

$JBAUD

Specify RS-232, RS-422 (output) communication rate

$JBIN

Specify binary messages to output to specific ports (see 
Table 3-4)

$JDIFF

Query or specify differential correction mode

$JGEO

Query or specify SBAS for current location and SBAS satellites

$JI

Query unit’s serial number and firmware versions

$JOFF

Turn off all data messages

$JQUERY,GUIDE

Query accuracy suitability for navigation

Summary of Contents for V102 G





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands