Hemisphere GPS V102 G User Manual Download | Manualshive

Page: 25 / 60

background image

20

Chapter 2: Installation

Connecting the power/data cable

1.

Align the cable connector keyway with the V102 connector key.

2.

Rotate the cable ring clockwise until it locks. The locking action is
firm, but you will feel a positive “click” when it has locked.

3.

Tighten the clamp securing the cable to the V102.

Note:

See “V102 Dimensions” on page 13 for information on routing the

power/data cable.

Make sure the connector
keyway on the cable matches
up with the connector key on
the V102

Cable connector keyway

V102 connector key

Cable ring

«
...
23
24
25
26
27
...
»

Summary of Contents for V102 G





























































Reviews:

No comments

Related manuals for V102 G

Brand: Tokai Pages: 20

Brand: Zhong Shan Anders Electronics Pages: 5

DigiTRU Diversity UB-33B

Brand: Nady Systems Pages: 6

Box Design BT Box S2

Brand: Pro-Ject Audio Systems Pages: 6

Brand: Show Pages: 7

In-Sight 8000 Series

Brand: Cognex Pages: 116

Brand: Jensen Pages: 20

Brand: MadBoy Pages: 13

Brand: RCA Pages: 20

Brand: RCA Pages: 27

Brand: Suzuki Pages: 150

Brand: Kenwood Pages: 30

Brand: Kenwood Pages: 44

Brand: Kenwood Pages: 36

Brand: Kenwood Pages: 42

Brand: Kenwood Pages: 34

Brand: Kenwood Pages: 48

Brand: Kenwood Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands