manualshive.com logo in svg

Hemisphere GPS V102 G, User Manual

Share
Download
Hemisphere GPS V102 G User Manual Download Page 29

24

Chapter 2: Installation

Serial Ports

The V102 offers position and heading data via two full-duplex (bi-directional) 
RS-232 serial ports. In addition to outputting data, these ports are used for 
firmware upgrades.

Selecting Baud Rates and Message Types

When selecting your baud rate and message types, use the following 
calculation to determine your baud rate for your required data throughput.

Messages * Message output rate * Message length (bytes) * bits in byte
Ex: 5 * 20Hz * 40 bytes * 10 = 40,000 bits/sec

For information on message output rates refer to GPS Technical Reference 
available from the Hemisphere GPS website at 

www.hemispheregps.com

.

Configuring the Ports

You may configure Port A or Port C of the GPS receiver to output any 
combination of data that you want. Port A can have a different configuration 
from Port C in terms of data message output, data rates, and the baud rate of 
the port. This allows you to configure the ports independently based upon 
your needs. For example, if you want one generalized port and one 
heading-only port, you can configure the ports as follows:

•

Port A to have GPGGA, GPVTG, GPGSV, GPZDA, and GPHDT all 
output at 1 Hz over a 9600 baud rate

•

Port C to have GPHDT and GPROT output at their maximum rate of 
20 Hz over a 19200 baud rate

A personal computer (PC) typically uses a DB9-male connector for RS-232 
serial port communications.

Note:

 For successful communications use the 8-N-1 protocol and set the 

baud rate of the V102’s serial ports to match that of the devices to which they 
are connected. Flow control is not supported.

Summary of Contents for V102 G





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands