Hemisphere GPS V102 G User Manual Download | Manualshive

Page: 17 / 60

background image

12

Chapter 2: Installation

Mounting Options

The V102 allows for two different mounting options: flush mount and pole
mount.

•

Flush mount - The bottom of the V102 contains four M8 holes for
flush mounting the unit to a flat surface (see Figure 2-6 on page 13).

•

Pole mount - The bottom of the V102 contains a mounting hole (1"
thread, 0.9" depth) for easy pole mounting. Hand tighten until snug
(do not overtighten). The set screws on the long sides of the base
(see middle drawing in Figure 2-6 on page 13) allow you to secure
the V102 in place (3/16" Allen wrench not included).

«
...
15
16
17
18
19
...
»

Summary of Contents for V102 G





























































Reviews:

No comments

Related manuals for V102 G

Brand: Bang & Olufsen Pages: 20

Brand: Bang & Olufsen Pages: 24

BeoSound Ouverture

Brand: Bang & Olufsen Pages: 44

Brand: Harman Pages: 10

Brand: Harman Pages: 2

Brand: JB Systems Pages: 12

Brand: V-TEK Pages: 4

Brand: AEA Pages: 8

Brand: MediaRange Pages: 16

Brand: Eton Pages: 2

Brand: Audio Technica Pages: 2

Brand: Audio Technica Pages: 1

Brand: Audio Technica Pages: 2

Brand: Audio Technica Pages: 4

Brand: Black Box Pages: 14

Brand: TAG Heuer Pages: 8

Brand: Hyundai Pages: 35

Brand: Hyundai Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands