Hemisphere GPS V102 G User Manual Download

Page: 4 / 60

V102 GPS Compass User Guide

iii

Contents

Chapter 1

Introduction

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter 2

Installation

Mounting Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

GPS Reception. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

V102 Environmental Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

VHF Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Mounting Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

V102 Alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

V102 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Power/Data Cable Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Flush Mount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Pole Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Powering the V102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Power Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Connecting to a Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Electrical Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Connecting the V102 to External Devices . . . . . . . . . . . . . . . . . . . . . . . . 22

Power/Data Cable Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Power/Data Cable Pinout Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 23

Summary of Contents for V102 G





























































Search results

Summary of Contents for V102 G

Reviews:

Related manuals for V102 G

Brands by name

Popular brands

Hemisphere GPS V102 G, User Manual

Search results

Summary of Contents for V102 G

Reviews:

Related manuals for V102 G

Brands by name

Popular brands