manualshive.com logo in svg

Hemisphere GPS V102 G, User Manual

Share
Download
Hemisphere GPS V102 G User Manual Download Page 26

V102 GPS Compass User Guide

21

Powering the V102

Power Considerations

For best performance use a clean and continuous power supply. The V102 
power supply features reverse polarity protection but will not operate with 
reverse polarity.

See Table B-3 on page 47 for complete power specifications.

Connecting to a Power Source

Before you power up the V102 you must terminate the wires of the power 
cable as required. There are a variety of power connectors and terminals on 
the market from which to choose, depending on your specific requirements.

Do not apply a voltage higher than 36 VDC. This will damage 

the receiver and void the warranty.

To interface the V102 power cable to the power source:

•

Connect the red wire of the cable’s power input to DC positive (+)

•

Connect the black wire of the cable’s power input to DC negative (-)

The V102 will start when an acceptable voltage is applied to the power leads 
of the extension cable.

Electrical Isolation

The V102’s power supply is isolated from the communication lines and the 
PC-ABS plastic enclosure isolates the electronics mechanically from the 
vessel (addressing the issue of vessel hull electrolysis).

Summary of Contents for V102 G





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands