manualshive.com logo in svg

Hemisphere GPS V102 G, User Manual

Share
Download
Hemisphere GPS V102 G User Manual Download Page 11

6

Chapter 2: Installation

Mounting Location

This section provides information on determining the best location for the 
V102.

GPS Reception

When considering where to mount the V102, consider the following GPS 
reception recommendations:

•

Consider GPS (and hence SBAS) reception, ensuring there is a clear 
view of the sky available to the V102 so the GPS and SBAS satellites 
are not masked by obstructions that may reduce system 
performance

•

Since the V102 computes a position based on the internal primary 
GPS antenna element, mount the V102 where you desire a position 
with respect to the primary GPS antenna (located on the end 
opposite the recessed arrow on the underside of the enclosure)

•

Locate any transmitting antennas away from the V102 by at least 
several feet to ensure tracking performance is not compromised, 
giving you the best performance possible

•

Make sure there is enough cable length to route into the vessel to 
reach a breakout box or terminal strip

•

Do not locate the antenna where environmental conditions exceed 
those specified in Table B-5 on page 48

Summary of Contents for V102 G





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands