HELI green Series Operator'S Manual Download

Page: 9 / 82

power and direction of the wind outside, so do no work in strong wind to make sure

people and truck safety.

3. Travelling road

(1) Prohibit travel on public road

Reach truck is the special vehicle for indoor use.

It is different to go through ramp and rough road for its small and compact

structure. Reach truck will upset if go through ramp and rough road. In other hands, it

will block the travel of other vehicle and person’s pas for its low speed. If the wheel is

out of round or the status of the road surface is not good, it will raise the running

noise.

Prohibit travel on public road. Only use indoor.

4. Selecting driver

(1) Wear safety clothes

Please wear proper safety clothes when driving. Improper clothes may be caught

by operating levers or pedal which may cause truck mis-moving.



Be sure to wear safety helmet and safety shoes.



Please wear other necessary protective clothes according to working area

condition

(2) Safety education on goods stacking

Summary of Contents for green Series



















































































Search results

Summary of Contents for green Series

Reviews:

Related manuals for green Series

Brands by name

Popular brands

HELI green Series, Operator'S Manual

Search results

Summary of Contents for green Series

Reviews:

Related manuals for green Series

Brands by name

Popular brands