Harman Kardon AVR45, Owner'S Manual

Page: 21 / 94

System Configuration
18
AVR45 120 volt Rev (f) 7/1/98
When
LARGE
is selected, a full-
range output will be sent to the
front left and right outputs, and
NO low-frequency signals will be
sent to the subwoofer output.
5. When you have completed your
selection for the front channel, press
the
Set
button
i ˜
, and then
press the
⁄ / ¤
buttons
g
on the
remote or the
Selector
buttons
¸
on the front panel to change the dis-
play to
CEN SPEAKER
.
6. Press the
Set
button i ˜ again,
and use the
⁄ / ¤
buttons g on
the remote, or the
Selector
buttons
¸ on the front panel, to select the
option that best describes your system
based on the speaker definitions
shown above.
When
CEN SP SMALL
is
selected, low-frequency center
channel sounds will be sent to the
subwoofer output only. Note that if
you choose this option and there is
no subwoofer connected, you will
not hear any low-frequency sounds
from the center channel speaker.
When
CEN SP LARGE
is
selected, a full-range output will be
sent to the center speaker output,
and NO center channel signal will
be sent to the subwoofer output.
When
CEN SP NONE
is selected,
no signals will be sent to the center
channel output. The receiver will
operate in a “phantom” center
channel mode and center channel
information will be sent to the left
and right front channel outputs.
7. When you have completed your
selection for the center channel, press
the
Set
button
i ˜
, and then
press the
⁄ / ¤
buttons g on the
remote or the
Selector
buttons ¸
on the front panel to change the
display to
SUR SPEAKER
.
8. Press the
Set
button i ˜ again,
and then use the
⁄
/
¤
buttons g
on the remote or the
Selector
buttons
¸
on the front panel to
select the option that best describes
your system based on the speaker
definitions shown above.
When
SUR SP SMALL
is
selected, low-frequency surround
channel sounds will be sent to the
subwoofer output only. Note that if
you choose this option and there is
no subwoofer connected, you will
not hear any low-frequency sounds
from the surround speaker.
When
SUR SP LARGE
is selected,
a full-range output will be sent to the
surround channel outputs, and NO
surround channel signals will be sent
to the subwoofer output.
When
SUR SP NONE
is selected,
surround sound information will be
split between the front left and front
right outputs. Note that for optimal
performance when no surround
speakers are in use, the Dolby 3
Stereo mode should be used instead
of Dolby Pro Logic.
9. When you have completed your
selection for the surround channel,
press the
Set
button i ˜ , and
then press the
⁄ / ¤
buttons g on
the remote or the
Selector
buttons ¸
on the front panel to change the display
to
SÐW SPEAKER
.
10. Press the
Set
button i ˜ , and
then press the
⁄
/
¤
buttons
g
on
the remote or the
Selector
buttons
¸
on the front panel to select the option
that best describes your system.
Select
S-W SP ON
if a subwoofer
is connected to your system.
Select
S-W SP OFF
if a subwoofer is
NOT connected to your system. Note
that when no subwoofer is selected,
low-frequency sounds below 100Hz
will be sent to the front left/right
speakers, provided that the selection
in step 4, above, has been set to
LARGE
. Otherwise, no low-frequency
sounds will be heard. This option is
not available when the front, center or
surround speakers are set to
SMALL
.
AVR45 om (Eng,Fr) 9/15/98 1:19 PM Page 18