Harman Kardon AVR 145 Owner'S Manual Download

Page: 42 / 50

PROGRAMMING THE REMOTE

Example: One blink, followed by a one-second
pause, followed by six blinks, followed by a one-
second pause, followed by four blinks indicates
that the code has been set to 164.

For future reference enter the Setup Codes for the
equipment in your system here:

DVD ____________ CD ________________

VID1/VCR ________ VID3/TV __________

VID2/CBL/SAT ______________________

TAPE ______________________________

Macro Programming

Macros enable you to easily repeat frequently
used combinations of commands with the press of
a single button on the AVR’s remote control. Once
programmed, a macro will send out up to 19 dif-
ferent remote codes in a pre-determined sequen-
tial order enabling you to automate the process of
turning on your system, changing devices, or other
common tasks. The AVR’s remote can store up to
five separate macro command sequences, one
that is associated with the

Power On

button

, and four more that are accessed by pressing

the

Macro

buttons

1. To start programming a macro, press the

Mute

button

and the

Macro

button

to be

programmed or the

Power-On

button

at the

same time. Note that the latest selected

Input

Selector

will light red, and the

Program

Indicator

will flash amber.

2. Enter the steps for the macro sequence by
pressing the button for the actual command step.
Although the macro may contain up to 19 steps,
each button press, including those used to
change devices, counts as a step. The

Program

Indicator

will flash green twice to confirm

each button press as you enter commands.

NOTE:

While entering commands for Power On of

any device during a macro sequence, press the

Mute

button

. DO NOT press the

Power ON

button

• Remember to press the appropriate

Input

Selector

button

before functions are

changed to another device. This is also needed for
the

AVR Selector

button

itself, as long as

it’s not lit red and AVR functions shall be
programmed.

3. When all the steps have been entered, press
the

Sleep

button

to enter the commands.

The red light under the

Input Selector

will blink and then turn off and the

Program

Indicator

will flash green twice to confirm

the macro to be programmed.

Example:

To program the

Macro 1

button

so that it turns on the AVR, TV and a Sat-Receiver,
follow these steps:

• Press the

Macro 1

button

and

Mute

buttons at the same time and then release them.
• Note that the

Program Indicator

will flash

amber.
• Press the

AVR Selector

• Press the

Mute

button to store the AVR’s

power on command.
• Press the

VID 2 Input Selector

button

indicate the next command is for “TV”.
• Press the

Mute

button to store the TV

Power On Command.
• Press the

VID 3 Input Selector

button

to indicate the next command is for “Sat-
Receiver”.
• Press the

Mute

button to store the Sat-

Receiver Power On command.
• Press the

Sleep/Channel Up

button

complete the process and store the macro
sequence.

After following these steps, each time you press
the

Macro 1

button

, the remote will send

all Power On commands.

Erasing Macro Commands

To remove the commands that have been pro-
grammed into one of the Macro buttons, follow
these steps:

1. Press the

Mute

button

and the

Macro

button

that contains the commands you

wish to erase.

2. Note that the

Program Indicator

will

flash amber, and the red LED under the

Input

Selector

last used will turn on.

3. Within ten seconds, press the

Surround

Mode Selector/Channel Down

button

4. The red LED under the

Selector

will go out,

and the

Program Indicator

will turn green

and flash three times before it goes out.

5. When the

Program Indicator

goes out,

the Macro has been erased.

Programmed Device Functions

Once the AVR’s remote has been programmed for
the codes of other devices, press the appropriate

Input Selector

to change the remote from

control over the AVR to the additional product.
When you press any of these buttons, it will briefly
flash in red to indicate that you have changed the
device being controlled.

When operating a device other than the AVR, the
controls may not correspond exactly to the func-
tion printed on the remote or button. Some com-
mands, such as the volume control, are the same
as they are with the AVR. Other buttons will
change their function so that they correspond to a
secondary label on the remote. For example, the
Sleep and Surround mode selector buttons also
function as the Channel Up and Channel Down
buttons when operating most TV sets, VCRs or
Sat-Receivers.

For some products, however, the function of a
particular button does not follow the command
printed on the remote. In order to see which
function a button controls, consult the Function
List tables printed on page 44-45. To use those
tables, first check the type of device being
controlled (e.g., TV, VCR). Next, look at the
remote control diagram on page 44. Note that
each button has a number on it.
To find out what function a particular button has
for a specific device, find the button number on
the Function List and then look in the column for
the device you are controlling. For example,
button number 45 is the”Direct” button for the
AVR, but it is the “Favorite” button for many
cable television boxes and satellite receivers.
Button number 31 is the Delay button for the
AVR, but the Open/Close button for CD players.

Note that the numbers used to describe the
button functions above and on page 44 for the
purposes of describing how a button operates are
a different set of numbers than those used in the
rest of this manual to describe the button
functions for the AVR.

Notes on Using the AVR
Remote With Other Devices.

• Manufacturers may use different code sets for
the same product category. For that reason, it is
important that you check to see if the code set
you have entered operates as many controls as
possible. If it appears that only a few functions
operate, check to see if another code set will
work with more buttons.

• Depending on the brand and product type used
the functions listed in the Function List tables
may not correspond with the function the unit
reacts on the command. In these cases it’s a
good idea to edit the reaction of the unit into the
corresponding line of the table or to set up a sep-
arate list.

• When a button is pressed on the AVR remote, the
red light under the

Input Selector

for

the product being operated should flash briefly. If
the Device Control Selector flashes for some but
not all buttons for a particular product, it does
NOT indicate a problem with the remote, but
rather that no function is programmed for the
button being pushed.

Volume Punch-Through

The AVR’s remote may be programmed to operate
the

Volume Control

and the

Mute

from either the TV or the AVR in conjunction with
any of the devices controlled by the remote. For
example, since the AVR will likely be used as the
sound system for TV viewing, you may wish to
have the AVR’s volume activated although the
remote is set to run the TV. Either the AVR or TV
volume control may be associated with any of the
remote´s devices.

Programming the Remote

30935_AVR145_ENG 01/12/06 9:53 Side 42