manualshive.com logo in svg

Hardi HC 8500, Operator'S Manual, Page: 99 / 184

Share
Download
Hardi HC 8500 Operator'S Manual Download Page 99

4 - System setup

4.73

Swath Section Offsets

The Implement Offsets screen opens. On a typical HARDI® configuration, this screen may consist of up to three tabs:

•

Implement tab.

•

Liquid with Hardi tab.

•

Boom Control tab.

Implement tab

Implement Modelling:

Implement Type:

•

Standard

•

Hardi SafeTrack

˜

ATTENTION! For IntelliTrack sprayers, select 
the “Hardi SafeTrack” option.

Hitch to Axle Distance:

Press 

 to type in value.

Type in the measured value from Hitch of the 
sprayer to the axle.

Implement Rear Hitch:

Here is no relevant settings for HARDI® 
sprayers.

Liquid with Hardi tab

Forward/Backward Distance from Hitch:

•

Set distance between the hitch eye and the 
nozzles.

Left/Right Distance from center line:

•

For asymmetric booms. As HARDI® booms 
are never asymmetric, this option must be set 
to 0 cm. Left or Right selection does not 
matter.

Boom Control tab

Forward/Backward Distance from Hitch:

•

Set distance between the hitch eye and the nozzles.

Left/Right Distance from center line:

•

For asymmetric booms. As HARDI® booms are never asymmetric, this option must be set to 0 cm. Left or Right selection 
does not matter.

Configuration

Select Your Specific 

Configuration

Offsets

Implement Offsets: Hardi Commander

Implement

Liquid with Hardi

Implement Modeling

Implement Provides a Rear Hitch

Hitch to Axle 

Distance

Lateral Offset from Centerline

Left

Implement Type

Standard

Front Hitch to Rear Hitch

Implement Rear Hitch

Heading 

Aggressiveness

Boom Control

Advanced Swath Offsets

Implement Offsets: Hardi Commander

Implement

Liquid with Hardi

Boom Control

Forward/Backward Distance from Hitch

Left/Right Distance from Centerline

Left

25 ft Behind

Summary of Contents for HC 8500

























































































































































































Reviews:

No comments