Hardi HC 8500 Operator'S Manual Download Page 46

Page: 46 / 184

4 - System setup

4.20

12.

Enter Distance from Antenna Height to
Ground:

Press

to type in value.

Press

to confirm selection.

13.

Hitch Settings:

Press Hitch to view data already typed
in step 7.

Press

to confirm selection.

14.

Check the data in the overview.

Press

to confirm selection.

ATTENTION! If Offsets need to be corrected,
then press the

button to change the

antenna settings for the Selected Vehicle in
the drop down menu, before confirming
selection.

Vehicle Offsets: JD 4630

Antenna

Hitch

Enter Distance from Vehicle References to the Antenna

Antenna Location from

Rear Axle

Antenna Location from

Centerline

Antenna Height from

Ground

In Front

Left

Vehicle Offsets: JD 4630

Antenna

Hitch

Enter Distance from Rear Axle to the Following Locations

Rear Drawbar

Rear Lift Arms

Front Lift Arms

Operating Configuration Wizard: Vehicle

Select Vehicle

JD 4630

Offsets

Antenna Location from Rear Axle

Antenna Location from Centerline

Antenna Height from Ground

Rear Drawbar

Rear Lift Arms

Front Lift Arms

Summary of Contents for HC 8500

























































































































































































Search results

Summary of Contents for HC 8500

Reviews:

Hardi HC 8500, Operator'S Manual, Page: 46 / 184

Search results

Summary of Contents for HC 8500

Reviews: