manualshive.com logo in svg

Hardi HC 8500, Operator'S Manual, Page: 7 / 184

Share
Download
Hardi HC 8500 Operator'S Manual Download Page 7

Table of contents

TOC.3

7 - Fault finding

Devices ..................................................................................................................................................1

Device Information  ............................................................................................................................................................................................... 1

ISOBUS ...................................................................................................................................................3

ISOBUS VT  ................................................................................................................................................................................................................... 3
VT Alarms and Trouble Codes ........................................................................................................................................................................ 4

ISOBUS Modules  ....................................................................................................................................5

Modules not found  ............................................................................................................................................................................................... 5
ISOBUS Configuration Mismatch  ................................................................................................................................................................. 6

GPS ........................................................................................................................................................7

GPS Information ...................................................................................................................................................................................................... 7
GPS Button  ................................................................................................................................................................................................................. 7
GPS Information - General Tab  ...................................................................................................................................................................... 7
GPS Information - NTRIP  ................................................................................................................................................................................. 11

8 - Technical specifications

Specifications ........................................................................................................................................1

Technical Specifications ..................................................................................................................................................................................... 1
Sprayer Offsets ......................................................................................................................................................................................................... 1

Appendix ...............................................................................................................................................2

Current File Formats ............................................................................................................................................................................................. 2
Legacy File Formats .............................................................................................................................................................................................. 2

9 - Warranty

Warranty policy and conditions  ............................................................................................................1

Summary of Contents for HC 8500

























































































































































































Reviews:

No comments