Hardi HC 8500 Operator'S Manual Download Page 67

Page: 67 / 184

4 - System setup

4.41

25.

Enter Vehicle Name:

Press

button to change name.

Press

to confirm name.

26.

Press

to enter values for Antenna Offsets.

27.

Vehicle Offsets:

Press to enter Antenna Location from
Rear Axle.

Select if the Antenna is In Front or
Behind the Rear Axle.

Press to enter Antenna Location from
the sprayers center line.

Select if the Antenna is to the Left or
Right of the sprayers center line.

Press to enter Antenna Height from
Ground.

Press “Steering” to continue with
Steering Type selection.

Implement Wizard: Vehicle Name

Enter Vehicle Name

Hardi Saritor

Operating Configuration Wizard: Vehicle

Select Vehicle

Offsets

Antenna Location from Rear Axle

Antenna Location from Centerline

Antenna Height from Ground

Dispensing Location from Rear Axle

Dispensing Location from Centerline

Behind

Vehicle Offsets: Hardi Saritor

Antenna

Steering

In Front

Left

Enter Distance from Vehicle References to the Antenna

Enter Location from

Rear Axle

Enter Location from

Centerline

Antenna Height from

Ground

Summary of Contents for HC 8500

























































































































































































Search results

Summary of Contents for HC 8500

Reviews:

Hardi HC 8500, Operator'S Manual, Page: 67 / 184

Search results

Summary of Contents for HC 8500

Reviews: