Hardi HC 8500 Operator'S Manual Download Page 66

Page: 66 / 184

4 - System setup

4.40

22.

Application Point Offset:

Press to select “Behind”.

Press

to enter the distance

from the rear axle of the vehicle to the
nozzles on the sprayer.

Press

confirm.

ATTENTION! For offsets see “Sprayer Offsets”
on page 8.1.

23.

Press

to confirm selection.

24.

Additional devices:

Press “Norac UC5” button to enable
the use of
AutoTerrain/AutoHeight/AutoSlant.

Press

continue.

ATTENTION! If the “Norac UC5” is not
enabled, the
AutoTerrain/AutoHeight/AutoSlant will not
be shown in the working screen.

Equipment Setup Wizard: Application Point Offset

Behind

Enter Distance from Rear Axle to Application Point

Implement Wizard: Application Channels

Type

Controller

Channel

Container

Liquid

Hardi

Main Tank

Liquid

Application

Direct

Injection

Granular

Application

Remove

Implement Wizard: Additional Devices

Norac UC5

OptRx Crop Sensor

Crop Sensor Settings

Sensing Width

Number of Sensors

Swath

Offsets

Note: Sensing Width should typically be set to the same

width as the implement.

Summary of Contents for HC 8500

























































































































































































Search results

Summary of Contents for HC 8500

Reviews:

Hardi HC 8500, Operator'S Manual, Page: 66 / 184

Search results

Summary of Contents for HC 8500

Reviews: