Hardi HC 8500 Operator'S Manual Download Page 151

Page: 151 / 184

5 - Operation

5.17

Edit Headlands

Press Edit Headlands button.

Select a headland from list.

•

Press

to add a driven headland.

•

Press

to delete selected headland.

•

Press

to delete all driven headlands.

•

Press

to return to Headland Options

screen.

•

Press

to load selected headland.

This screen will vary depending on type of
headland.

Headland Alarm Settings

Press

button.

•

Alert Distance

Distance from approaching headland at
which display will warn user of upcoming
headland.

•

Alert Duration

Time length from approaching headland at
which display will warn user of upcoming
headland.

•

Audible Alarms

•

Approaching Headland.

•

Crossing Headland Boundary.

Map Screen with Headlands.

Edit Headlands

Clear All

Summary of Contents for HC 8500

























































































































































































Search results

Summary of Contents for HC 8500

Reviews:

Hardi HC 8500, Operator'S Manual, Page: 151 / 184

Search results

Summary of Contents for HC 8500

Reviews: