Hangar 9 Christen Eagle II 90 ARF Assembly Manual Download Page 4

Page: 4 / 36

Hangar 9 Christen Eagle II 90 ARF

Safety Precautions and Warnings

Read and follow all instructions and safety precautions

before use. Improper use can result in fire, serious injury

and damage to property.

Age Recommendation: Not for children under 14

years. This is not a toy.

COMPONENTS

Use only with compatible components. Should any

compatibility questions exist, please refer to the product

instructions, the component instructions or contact Horizon

Hobby, Inc.

FLIGhT

Fly only in open areas to ensure safety. It is recommended

flying be done at AMA (Academy of Model Aeronautics)

approved flying sites. Consult local ordinances before

choosing a flying location.

PROPELLER

Keep loose items that can get entangled in the propeller

away from the prop, including loose clothing or other objects

such as pencils and screwdrivers. Especially keep your

hands away from the propeller as injury can occur.

BATTERIES

Notes on Lithium Polymer Batteries

When used improperly, lithium polymer batteries are

significantly more volatile than alkaline or Ni-Cd/Ni-MH

batteries used in RC applications. Always follow the

manufacturer’s instructions when using and disposing of any

batteries. Mishandling of Li-Po batteries can result in fire

causing serious injury and damage.

SMALL PARTS

This kit includes small parts and should not be left

unattended near children as choking and serious injury

could result.

Contents of kit and Parts Listing

Replacement Parts

1. HAN501001

Fuselage with Hatch

2. HAN501002

Upper Wing Set

3. HAN501003

Lower Wing Set

4. HAN501004

Tail Set

5. HAN501005

Canopy Hatch

6. HAN501006

Fiberglass Cowling

7. HAN501008

Landing Gear with Fairings

8. HAN501009

Wing Tube Set

9. HAN501010

Wing Strut Set

10. HAN501013

Fiberglass Wheel Pants

11. HAN501014

Wheels and Tailwheel Assembly

Items Not Shown

HAN501007

Wing Transport Frames

HAN501011

Hardware Pack

HAN501012

Pushrod Set

HAN501015

Engine Mount Set with Spinner

HAN501016

Electric Power Mounting Set

Summary of Contents for Christen Eagle II 90 ARF





































Search results

Summary of Contents for Christen Eagle II 90 ARF

Reviews:

Related manuals for Christen Eagle II 90 ARF

Brands by name

Popular brands

Hangar 9 Christen Eagle II 90 ARF, Assembly Manual

Search results

Summary of Contents for Christen Eagle II 90 ARF

Reviews:

Related manuals for Christen Eagle II 90 ARF

Brands by name

Popular brands