background image

33

Hangar 9 Christen Eagle II 90 ARF

UNITED kINGDOM

Horizon Hobby Limited

Units 1-4 Ployters Rd

Staple Tye

Harlow, Essex

CM18 7NS

United Kingdom

[email protected]

+44 (0) 1279 641 097

GERMANy

Horizon Technischer Service

Hamburger Str. 10

25335 Elmshorn

Germany

[email protected]

+49 4121 46199 66

FRANCE

Horizon Hobby SAS

14 Rue Gustave Eiffel

Zone d’Activité du Réveil Matin

91230 Montgeron

+33 (0) 1 60 47 44 70

Compliance Information for the 

European Union

  

INSTRUCTIONS FOR DISPOSAL OF WEEE By 
USERS IN ThE EUROPEAN UNION

This product must not be disposed of with other waste. 

Instead, it is the user’s responsibility to dispose of their 

waste equipment by handing it over to a designated 

collection point for the recycling of waste electrical and 

electronic equipment. The separate collection and recycling 

of your waste equipment at the time of disposal will help to 

conserve natural resources and ensure that it is recycled in 

a manner that protects human health and the environment. 

For more information about where you can drop off your 

waste equipment for recycling, please contact your local city 

office, your household waste disposal service or where you 

purchased the product.

Academy of Model Aeronautics 

National Model Aircraft Safety Code

Effective January 1, 2011

A. GENERAL

A model aircraft is a non-human-carrying aircraft capable 

of sustained flight in the atmosphere. It may not exceed 

limitations of this code and is intended exclusively for 

sport, recreation and/or competition. All model flights must 

be conducted in accordance with this safety code and any 

additional rules specific to the flying site.

1. Model aircraft will not be flown:

(a) In a careless or reckless manner.
(b) At a location where model aircraft activities are prohibited.

2. Model aircraft pilots will:

(a) Yield the right of way to all man carrying aircraft.
b) See and avoid all aircraft and a spotter must be used when 

appropriate. (AMA Document #540-D-See and Avoid Guidance.)
(c) Not fly higher than approximately 400 feet above ground 

level within three (3) miles of an airport, without notifying the 

airport operator.
(d) Not interfere with operations and traffic patterns at any 

airport, heliport or seaplane base except where there is a mixed 

use agreement.
(e) Not exceed a takeoff weight, including fuel, of 55 pounds 

unless in compliance with the AMA Large Model Aircraft 

program. (AMA Document 520-A)
(f) Ensure the aircraft is identified with the name and address or 

AMA number of the owner on the inside or affixed to the outside 

of the model aircraft. (This does not apply to model aircraft 

flown indoors).
(g) Not operate aircraft with metal-blade propellers or with 

gaseous boosts except for helicopters operated under the 

provisions of AMA Document #555.
(h) Not operate model aircraft while under the influence of 

alcohol or while using any drug which could adversely affect the 

pilot’s ability to safely control the model.
(i) Not operate model aircraft carrying pyrotechnic devices which 

explode or burn, or any device which propels a projectile or 

drops any object that creates a hazard to persons or property.

Exceptions:

•  Free Flight fuses or devices that burn producing smoke and are 

securely attached to the model aircraft during flight.

•  Rocket motors (using solid propellant) up to a G-series size may 

be used provided they remain attached to the model during flight. 

Model rockets may be flown in accordance with the National 

Model Rocketry Safety Code but may not be launched from model 

aircraft.

•  Officially designated AMA Air Show Teams (AST) are authorized 

to use devices and practices as defined within the Team AMA 

Program Document (AMA Document #718).

(j) Not operate a turbine-powered aircraft, unless in compliance 

with the AMA turbine regulations. (AMA Document #510-A).

3.  Model aircraft will not be flown in AMA sanctioned events, air 

shows or model demonstrations unless:

(a) The aircraft, control system and pilot skills have successfully 

demonstrated all maneuvers intended or anticipated prior to the 

specific event.
(b) An inexperienced pilot is assisted by an experienced pilot.

4.  When and where required by rule, helmets must be properly 

worn and fastened. They must be OSHA, DOT, ANSI, SNELL or 

NOCSAE approved or comply with comparable standards.

B. RADIO CONTROL (RC)

1.  All pilots shall avoid flying directly over unprotected people, 

vessels, vehicles or structures and shall avoid endangerment of 

life and property of others.

2.  A successful radio equipment ground-range check in accordance 

with manufacturer’s recommendations will be completed before 

the first flight of a new or repaired model aircraft.

3.  At all flying sites a safety line(s) must be established in front of 

which all flying takes place (AMA Document #706-Recommended 

Field Layout):

(a) Only personnel associated with flying the model aircraft are 

allowed at or in front of the safety line.
(b) At air shows or demonstrations, a straight safety line must 

be established.
(c) An area away from the safety line must be maintained for 

spectators.
(d) Intentional flying behind the safety line is prohibited.

4.  RC model aircraft must use the radio-control frequencies 

currently allowed by the Federal Communications Commission 

(FCC). Only individuals properly licensed by the FCC are 

authorized to operate equipment on Amateur Band frequencies.

5.  RC model aircraft will not operate within three (3) miles of 

any pre-existing flying site without a frequency-management 

agreement (AMA Documents #922- Testing for RF Interference; 

#923- Frequency Management Agreement)

Summary of Contents for Christen Eagle II 90 ARF





































Reviews: