background image

HQ Infinity User Manual 

 | 31

To wind the bobbin

The Infinity comes with a separate bobbin winder. For full instructions about using the bobbin winder, see 

the instruction manual that was packaged with the bobbin winder.

 

ONLINE

: For more information about using the bobbin winder, watch the video 

Using the Bobbin 

Winder

 at: 

http://www.handiquilter.com/videos/hq-infinity/245/

.

 

To insert the bobbin into the bobbin case

 

ONLINE

: For more information about inserting the bobbin into the bobbin case, watch the video 

Inserting the Bobbin

 at: 

http://www.handiquilter.com/videos/hq-infinity/225/

.

 

U

CAUTION

: To prevent personal injury always turn off the front power switch while inserting and/or 

removing bobbin case or anytime your hands are near the needle area, such as when you change 

the needle.

1.  Place the bobbin in the bobbin case so that the 

thread pulls off clockwise when viewing the 

open side. 

2.  Slide the thread through the slot and under the 

tension spring, leaving approximately five to six 

inches of thread hanging loose. 

To test bobbin tension 

The bobbin tension is the foundation tension for the entire machine. Always set the bobbin tension first. 

 

NOTE

: Check the bobbin tension each time a new bobbin is inserted.

 

ONLINE

: For more information about testing and adjusting the bobbin tension, watch the video 

Testing and Adjusting Bobbin Tension

 at: 

http://www.handiquilter.com/videos/hq-infinity/248/

.

1.  With the bobbin properly in the bobbin case, hold the bobbin case in the palm of your hand with the 

open end facing up. 

2.  Wrap the thread two to three around the index finger of the opposite hand and lift the bobbin up. The 

bobbin case should lift up on its side, and slightly lift out of your hand. If the bobbin will not lift up on 

its side, the bobbin tension is too loose and if it lifts out of your hand, the bobbin tension is too tight.

Summary of Contents for Infinity 26 QM33001



























































































Reviews: