Haier GE DDT700S N0 Series Technical Service Manual Download Page 65

Page: 65 / 78

– 65 –

The Thermistor is located inside the turbidity

sensor. The thermistor monitors water

temperature in the tub. If the thermistor opens or

shorts it will cause an error (see

Consumer Error

Mode

in the

Electronic Controls

section of this

service guide). If it fails in open or shorted, the

control will default to the longest time algorithm.

Thermistor Specifications

Turbidity Sensor Calibration

Calibration occurs every 100 cycles. After the

final rinse but before dry, the control will add three

extra rinse cycles. The first cycle will fill, circulate

two minutes and drain. The second cycle will

be a fill and drain. The third cycle will be a fill,

circulate, calibrate and drain. The cycle will now

advance to dry and complete.

Replacement controls will enter a calibration

at the end of the first cycle that the control

completes, as mentioned above. If the first cycle

is interrupted and calibration does not occur,

calibration will retry on the next cycle, until it is

completed. Calibration will not occur on demand.

Turbidity Sensor Diagnostics

If the turbidity sensor fails open or shorted, the

control will default to the maximum fills and

circulation time that the control is programmed for.

Use

Consumer Error Mode

to look for Turbidity

Sensor Faults.

VOLTAGE RESISTANCE TEMPERATURE

.95

20066

50°F

1.56

10450

75°F

2.25

5824

100°F

2.91

3411

125°F

3.48

2081

150°F

3.91

1330

175°F

To check the thermistor, access the Main Control

(see the

Electronic Controls

section of this

service guide), check resistance on connector

J806, pin 11, YR to pin 8, RN. The sensor may

also be removed and the two outside terminals

may be checked. Use the table to the left to

calculate the correct resistance reading.

Thermistor

Summary of Contents for GE DDT700S N0 Series















































































Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands

Haier GE DDT700S N0 Series, Technical Service Manual

Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands