Haier GE DDT700S N0 Series Technical Service Manual Download Page 69

Page: 69 / 78

– 69 –

Mounting Tabs

The upper sprayer provides a gentle shower down to the top rack.

The spray bracket is attached to the main conduit by means of tabs.

To remove the upper spray system, use a small screw-driver to release the spray system bracket tabs

from the main conduit.

The Bottle Wash is designed to wash sports bottles, baby bottles, or any dishwasher safe container

with a smaller mouth which blocks water from entering the container using normal spray arm jets. This

feature insures clean containers. Water is active anytime that the upper spray arm is operational.

Selecting the bottle wash option on the control changes the wash algorithm. The upper spray arm and

bottle wash jets are cycled for a longer time, and 23 minutes is added to most cycles when selected.

Illustrations for the bottle wash system and removal may be found under

Upper Rack

in the

Racks

section of this service guide.

Cover

Hose

Mid Conduit

Bottle Wash Manifold

Clips

Bottle Wash System (Some Models)

Upper Spray System

Summary of Contents for GE DDT700S N0 Series















































































Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands

Haier GE DDT700S N0 Series, Technical Service Manual

Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands