Haier GE DDT700S N0 Series Technical Service Manual Download Page 30

Page: 30 / 78

– 30 –

10. Standing in front of the dishwasher, open the

door a few inches, then lift the door and hinge

arms off of the offset leg.

When installing the door onto the dishwasher,

make sure the hinge pins located on the hinge

arms are placed fully on the offset legs (both

sides).

8. Slide the cable into the cable clip to prevent

the spring from disconnecting from the cable.

CAUTION

: If the cable is released, the spring and

cable may become disconnected. Depending

on the model and installation, reconnecting may

require the dishwasher to be removed from

installation.

The cable seated correctly into the clip is shown

below.

9. Repeat steps 5 through 8 on the opposite

side.

Summary of Contents for GE DDT700S N0 Series















































































Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands

Haier GE DDT700S N0 Series, Technical Service Manual

Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands