Haier GE DDT700S N0 Series Technical Service Manual Download Page 48

Page: 48 / 78

– 48 –

A CSM is a protective device that is part of GE, Profile, Haier, Café and Monogram Dishwashers and

located on the main control board. This device is designed to trip if current leakage to ground is above

20mA ± 5mA is detected. The CSM functions similar to commercially available GFCI's. If tripped, the

dishwasher is non-responsive. All the LED's will flash and models with a display will show 888 until the

CSM is reset. Cycling power or entering Service Mode will reset the CSM. The Service LED on the

main control flashes to advise the control software is functioning.

The cause of tripping is likely external to the board itself. The board should only be replaced after

all other diagnostic tests have been completed and all other potential causes have been ruled out.

Potential causes of current leakage to ground could be due to water leaking onto a live component, a

component malfunction, or a fault within the wiring harness. If water caused the CSM to trip, the leak

must be repaired. The dishwasher may run until a leak causes the trip to reoccur. Resetting the CSM

without fixing the underlying issue will likely result in a repeat call. Always perform a visual inspection

of the exposed heating element, looking specifically for cracks, splits, or swelling of the sheath.

CSM Diagnostics

The CSM and Heater may be tested by running test 7 in

Service Mode

NOTE

: Normal water level must be present when checking the circulation pump, drain pump, and the

heater.

Circulation Pump

causes CSM to Trip

Drain Pump causes

CSM to Trip

Heater causes

CSM to Trip

Check for water Leak(s),as

dishwasher is running in Normal

cycle does it leak?

Replace Heater

Yes

Replace Circulation

Pump

Replace Drain Pump

Start a Normal Cycle. Did CSM

trip immediately?

Yes

Look for evidence of water leak under

the dishwasher, repair leak(s) as

needed and reset CSM

Use Service

Mode to Test

each Load

Repair leak and retest

CSM is Tripped

CSM (

Current Sense M

odule)

Summary of Contents for GE DDT700S N0 Series















































































Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands

Haier GE DDT700S N0 Series, Technical Service Manual

Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands