Haier GE DDT700S N0 Series Technical Service Manual Download Page 58

Page: 58 / 78

– 58 –

Use the flat-blade screw-driver to remove the

floating seal from the sump, using care not to

damage the inside sealing surface.

For diagnostic information, please see the

Motors Fuse

, located under

No Circulation and

Drain

in this section of this guide.

(

Continued next page

)

The circulation motor is a DC Brushed Motor; it

has onboard AC to DC rectification. Resistance

cannot be properly checked on this motor

because of the rectifier and diodes inside the

motor shield.

Circulation Pump Motor Assembly Removal

1. Disconnect power to the dishwasher.

Remove the toe kick panel, door and sump

(see

Door Removal

under

Door

, and

Sump

Module Removal

under

Sump Module

the

Tub and Structure

section of this guide).

2. Loosen the outlet wash motor (diverter)

clamp.

Use a large flat-blade screw-driver to slide the

circulation motor out of the floating seal. As

the pump assembly is removed from the seal,

slide the wash motor off of the hanger (use

care to not lose the hanger grommet), and

remove and discard the one time use clamp.

WARNING: GE Factory Service Technicians

are REQUIRED to follow Lockout / Tagout

(LOTO) 6 Step Process prior to beginning

repair.

Floating Seal Sealing Surface

Pump Assembly Grommet

Circulation Motor and Pump Assembly

Summary of Contents for GE DDT700S N0 Series















































































Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands

Haier GE DDT700S N0 Series, Technical Service Manual

Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands