Haier GE DDT700S N0 Series Technical Service Manual Download Page 56

Page: 56 / 78

– 56 –

Motors Fuse

A motors fuse is located on the main control board. If found open while testing for no circulation and

drain pump operation, the fuse and bad pump motor must be replaced. If 120 VAC is not present at

J703-3 to J703-4 for circulation pump or J703-1 to J703-2 for drain pump, remove and check the fuse

at the points shown in the below illustration. If an open fuse is found, replace the fuse and bad pump.

The Drain pump can be diagnosed by removing connector J703 from the control and check the

blue

yellow

wires using a multimeter on the highest resistance setting. If the reading is between 0.3 – 5.0

mega-ohm, then the drain pump is good. If it measures OL (overload or open) it indicates a bad drain

pump. If the drain motor checks OK, replace the circulation pump motor.

The circulation pump is a DC motor and cannot be checked for a resistance reading, it contains internal

diodes and rectifiers.

Pump Motors Fuse

Test Points

No Circulation and Drain

Circulation and Drain Pumps

will not run

Access main control, place dishwasher in Service

Mode,run circulation and drain tests. Check for

120 VAC on connector J703 pin 3 (OX) to pin 4

(CX) for circulation pump and pin 1 (NX) to pin 2

(YX). Is there 120 VAC?

Remove Sump Module to

check the AC wire harness

Is Fuse On Main

Control open?

Yes

Open

Replace

Harness

Diagnose drain pump, if drain pump checks OK,

Circulation pump is at fault. Replace Fuse and

inoperative Pump

Replace

Main

Control

Summary of Contents for GE DDT700S N0 Series















































































Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands

Haier GE DDT700S N0 Series, Technical Service Manual

Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands