Haier AB25S2SC1FA, Service Manual

Page: 163 / 182

161
14. ECO:
(1) Press ECO button and the display will show .
(2) ECO is valid under all modes, it is memorized among
switch of all modes.
(3) ECO function power-on or power-OFF is memorized.
15. Turbo/Quiet:
(1) Press button “Turbo”, display icon on remote LCD
display, display icon of fan speed; Press
button “Quiet”, display icon on remote LCD display,
display icon of fan speed.
(2) Turbo and QUIET functions can not exist at the same time,
the latter will replace the former.
(3) If Turbo function is set, press “SLEEP” button to exit
turbo, which means that setting SLEEP function while
canceling turbo function. At the same time, the icon
disappears and icon is shown; if QUIET function is set
at present, press button “SLEEP” while QUIET function is
still kept.
(4) This function is valid under the mode of COOL or HEAT.
(5) Turbo/QUIET functions are not memorized among switch
of all modes/the state of on or OFF.
16. IFP:
(1) Press “IFP” button, display , IFP function is set,
and press “IFP” button again to cancel.
(2) Press “Follow/Evade” button, display that expresses
following; press it again, display that expresses evading.
Press it the third time to cancel.
(3) If follow/evade functions are set, air-out angle will change
with position of people, so after setting these functions,
Four-side Embedment icons in all sides, up-and-down
SWING and left-and-right SWING icons will disappear.
(4) If air conditioner is in the state of HEALTH follow/
evade functions is set, HEALTH function is
cancelled, Four-side Embedment, up-and-down SWING
and left-and-right SWING icons will disappear.
17. FRESH:
(1) FRESH function is valid under the state of ON or OFF.
When air conditioner is OFF, press “FRESH” button,
display icon on LCD display to enter Fan mode and
low speed. Press “FRESH” button again, this function is
cancelled.
(2) After FRESH function is set, ON or OFF functions are kept.
(3) After FRESH function is set, mode switch function is kept.
18. 10 ° C Heating Function and ° C/ ° F function
Press “MENU/°F” button to set 10°C Heating function and
°C/°F function. 10°C Heating Function is valid only under the
mode of HEAT, and it is not memorized under the state of ON
or OFF.
19. HEATER:
(1) When HEAT mode is chosen and is displayed on LCD
display, pressing “HEATER” button can cancel and set
HEATER function.
(2) Auto mode will not start HEATER function automatically,
but can set or cancel HEATER function.
20. Timer:
(1) TIMER ON
• Press “TIMER ON” button, character “ON” is press
“+/-“ button to adjust, then press “CONFIRM” button to
if “CONFIRM” button is not pressed within 10 s, TIMER ON
function is cancelled.
• If time of TIMER ON is the same as that of clock at present,
character “ON” is always and can not be it is
necessary to readjust time.
• When the time of TIMER ON is end, the setting time and
(2) TIMER OFF
• Press “TIMER OFF” button, character “OFF” is
press “+/-“ button to adjust, then press “CONFIRM” to
if “CONFIRM” is not pressed within 10 s, TIMER OFF function
is cancelled.
• If time of TIMER OFF is the same as that of clock at present,
character “OFF” is always and can not it is
necessary to readjust time.
• When the time of TIMER OFF is end, the setting time and
character “OFF” disappear.
(3) TIMER ON/OFF
• After TIMER ON/OFF is set, remote will automatically judge
sequential order of ON/OFF, arrow indicates that the one
performed points to the one performed second.
• After the time of clock performed is end, corresponding
characters of timer “ON/OFF” disappear.
• If time of TIMER ON is the same as that of TIMER OFF, and
can not be corresponding character of the latter of
setting time is always it is necessary to readjust time
and again.
• If time of TIMER ON/OFF is the same as that of clock at
present, and can not be it is necessary to readjust
time and again.
(4) After setting timer, display the setting of timer and then
display time all the time, when timer is active, character “ON/
OFF” is always displayed.
21. /-:
• Press button “+/-“, time will change in terms of 1 min as unit,
pressing and holding the button will change quickly.
22. Clock:
• Press “Clock” button, “AM” or “PM” displayed at present are
to enter the state of clock adjustment, adjust clock and
then press “CONFIRM” to
• It is valid under the state of ON/OFF.
23. LIGHT:
No display on remote controller LCD, which is processed by
indoor unit.
24. RESET:
Perform one power on reset operation when RESET button is
pressed.
25. LOCK:
Press button Lock, display Lock symbol on LCD display,
buttons on remote controller can not be used, press button
Lock again to unlock.
26. CODE:
Function reserved.
27. INQUIRE
Function reserved.