Hachette Agora Bismarck Pack 04 Build Instructions Download Page 35

Page: 35 / 40

: ASSEMBLING THE ADMIRAL’S BRIDGE

Cut the railing

from frame

43-08

. Identify the

indents on either side of the centre point of the
railings (see detail image). Make two right angle
bends at these points.

Identify the next two bend points (red arrows) and
bend the railings outwards at right angles. Check the
fit of the railings on the deck (see step 3) and make
the final bends to part

at each end.

The railings fit along the front of the decking

43-06

Apply a little superglue to the bottom of the posts
of the railings

and fix in place.

Cut part

from frame

43-08

and bend it at the

indents, as shown, so that it fits along the starboard
side of the decking.

Use a tiny bit of superglue, applied to the bottom of
the posts, to fix the section of railing

in place on the

decking

43-06

Take the last section of railing

from frame

43-08

and bend it as shown, at the indents, to fit along the
port side of the decking.

43-06

AGORA

MODELS

AGORA

MODELS

Summary of Contents for Agora Bismarck Pack 04









































Search results

Summary of Contents for Agora Bismarck Pack 04

Reviews:

Related manuals for Agora Bismarck Pack 04

Brands by name

Popular brands

Hachette Agora Bismarck Pack 04, Build Instructions

Search results

Summary of Contents for Agora Bismarck Pack 04

Reviews:

Related manuals for Agora Bismarck Pack 04

Brands by name

Popular brands