Hachette Agora Bismarck Pack 04 Build Instructions Download Page 7

Page: 7 / 40

. FURTHER DETAILS FOR THE RADAR AND CONTROL CENTRE

Identify the two ladders

and cut them from part

34-13

. Glue the first ladder

on the starboard side of

the control centre

34-01

Glue the second ladder

in place on the port side of

the control centre

34-01

Cut the two ladders

from part

34-13

. Glue the first

ladder

to the back port side of the superstructure

(part

29-01

, behind the rangefinder).

Glue the second ladder

to the starboard side of the

superstructure, behind the rangefinder.

Check the fit of the radar antenna

34-14

on the front

of the radar unit

34-02

. It should protrude clearly

above the top of

34-02

. Fix in place with a little

superglue.

Attach the base of the radar unit

34-03

to the roof of

the control centre using a

(1.7 x 4 mm) screw.

29-01

34-02

34-01

34-14

34-03

34-01

PB 1.7x4

AGORA

MODELS

AGORA

MODELS

Summary of Contents for Agora Bismarck Pack 04









































Search results

Summary of Contents for Agora Bismarck Pack 04

Reviews:

Related manuals for Agora Bismarck Pack 04

Brands by name

Popular brands

Hachette Agora Bismarck Pack 04, Build Instructions

Search results

Summary of Contents for Agora Bismarck Pack 04

Reviews:

Related manuals for Agora Bismarck Pack 04

Brands by name

Popular brands