Hachette Agora Bismarck Pack 04 Build Instructions Download Page 40

Page: 40 / 40

. NEW ANCHOR RINGS

Turn the assembly around again and take the port
railing,

44-07

. Check the fit around the front port side

of the upper mast deck

44-01

and use a few drops of

superglue on the pegs at the bottom to fix it in place.

Turn the assembly round and glue the starboard
railing

44-08

in place around the starboard side of the

upper mast deck

44-01

Loosen the anchor rings

7-07

from both anchor

chains

7-06

and anchor shafts

7-09

as shown.

Take one of the two new anchor rings

44-09

and

use it to connect an anchor chain

7-06

to an anchor

shaft

7-09

In the same way, use the second anchor ring

44-09

connect the second anchor chain

7-06

to an anchor

shaft

7-09

Completed work

We have replaced the anchor rings and started the
assembly of the upper mast deck.

7-06

44-07

44-01

44-08

7-07

7-09

44-09

7-09

7-06

44-09

7-09

7-06

AGORA

MODELS

AGORA

MODELS

Summary of Contents for Agora Bismarck Pack 04









































Search results

Summary of Contents for Agora Bismarck Pack 04

Reviews:

Related manuals for Agora Bismarck Pack 04

Brands by name

Popular brands

Hachette Agora Bismarck Pack 04, Build Instructions

Search results

Summary of Contents for Agora Bismarck Pack 04

Reviews:

Related manuals for Agora Bismarck Pack 04

Brands by name

Popular brands