background image

37-06

37-04

37-07

38-02

3

3

37-07

3

37-07

3

4

5

36-01

11

07

08

09

10

Turn the foretop around so that you can fit the second 
part 

3

, in one of the recesses in the aft corners of the 

foretop deck 

37-07

. Again, make sure you have part 

3

 

facing the right way, in this case it faces outwards. Fix 
in place with a little superglue. 

Cut the three parts 

3

, from the frame 

38-03

. Identify 

the fixing point for the first part 

3

, on the recess  

on the forward end of the deck 

37-07

. Note that the 

flat side should face forwards. Fix in place with a 
little superglue.

Thread the motor cable 

36-01

 through the centre of 

the foretop command post gallery 

38-02

. Check that 

the triangular shapes of the foretop are aligned. Apply 
a little superglue around the base of part 

37-04

 and 

fix in place. 

Completed work

Accessories and a gallery have been fitted to the 
foretop command post.

Cut the door, 

5,

 and the set of three lockers, 

4

, from 

the frame 

38-03

. Test the fit on the foretop, noting the 

orientation, and fix in place with a little superglue.

Fix the third part 

3

 in place in the other corner  

of the foretop deck, again, with the flat side  
facing outwards.

20

20

AGORA

MODELS

PB

AGORA

MODELS

Summary of Contents for Agora Bismarck Pack 04









































Reviews: