Hachette Agora Bismarck Pack 04 Build Instructions Download Page 26

Page: 26 / 40

Stick the decking

40-05

in place on the searchlight

platform

40-03

. Apply a little glue to the base of the

searchlight and gently pull the cable

40-13

through

the channel in the platform so that the searchlight
sits on the deck covering, facing forward, as shown.

Hold the searchlight in place until the glue is firmly
set. Apply a little superglue to the two pegs on the
bottom of locker structure

40-04

and fix it in place

with the pegs in the holes in the decking

40-05

Take the two parts of the upper superstructure

40-01

and

40-02

and check the fit. Apply a little superglue

to the pegs on part

40-02

and fix it on to part

40-1

Take the ladder

40-12

and check the fit on the upper

superstructure.

Apply tiny drops of superglue to the four pegs (two at
each end) of ladder

40-12

and fix it in place with the

pegs in the holes on part

40-01

, as shown.

Pass the connector on the end of cable

40-13

through

the opening in the upper superstructure assembly
(arrow). Apply a very small amount of superglue to the
semicircular edge of the searchlight platform

40-03

Fix the searchlight platform in place on the front
of the upper superstructure.

40-03

40-05

40-13

40-05

40-04

40-02

40-01

40-12

40-01

40-12

40-03

40-13

40-03

AGORA

MODELS

AGORA

MODELS

Summary of Contents for Agora Bismarck Pack 04









































Search results

Summary of Contents for Agora Bismarck Pack 04

Reviews:

Related manuals for Agora Bismarck Pack 04

Brands by name

Popular brands

Hachette Agora Bismarck Pack 04, Build Instructions

Search results

Summary of Contents for Agora Bismarck Pack 04

Reviews:

Related manuals for Agora Bismarck Pack 04

Brands by name

Popular brands