Hachette Agora Bismarck Pack 04 Build Instructions Download Page 39

Page: 39 / 40

. DETAILS FOR THE UPPER MAST DECK

Fit the second part

in place through the opening in

part

, and glue the loop in place on the horizontal

peg of part

with a little superglue.

Glue the assembled ammunition hoist

44-06

in place

at the front of the upper mast deck

44-01

as shown.

Turn the assembly round and glue locker

in place

on the starboard side of the conning tower

44-05

, in

the same way as described for locker

Cut part

from frame

44-02

and check the fit on the

starboard side of the conning tower. Two pegs on part

fit into corresponding holes in part

44-05

. Apply a

little superglue to the pegs and fix in place.

Cut the locker,

, from the frame

44-02

and check the

fit on the port side of the conning tower

44-04

. A tab

at the base of the locker fits into a slot in the decking

44-03

. Apply a little superglue to the peg and fix in

place as shown.

Check the fit of the next locker,

, on the port side of

the conning tower

44-04

as shown. Glue in place in

the same way as described for locker

44-01

44-04

44-03

44-05

44-06

AGORA

MODELS

AGORA

MODELS

Summary of Contents for Agora Bismarck Pack 04









































Search results

Summary of Contents for Agora Bismarck Pack 04

Reviews:

Related manuals for Agora Bismarck Pack 04

Brands by name

Popular brands

Hachette Agora Bismarck Pack 04, Build Instructions

Search results

Summary of Contents for Agora Bismarck Pack 04

Reviews:

Related manuals for Agora Bismarck Pack 04

Brands by name

Popular brands