background image

Lanier R/C

 

1.20 Edge 540T 

A

lmost

 R

eady to 

F

ly 

 

 

WARNING! THIS IS NOT A TOY! 

THIS IS NOT A BEGINNERS AIRPLANE

 

This R/C kit and the model you will build from it is not a toy!  It is capable of serious bodily harm and property 
damage.  It is your responsibility, and yours alone - 

to build this kit correctly, properly install all R/C components and 

flying gear (engine, tank, radio, pushrods, etc. and to test the model and fly it only with experienced, competent help, 
using commonsense and in accordance with all safety standards as set forth in the Academy of Model Aeronautics Safety 
Code.  It is suggested that you join the AMA and become properly insured before attempting to fly this model.  If you are 
just starting R/C modeling, consult your local hobby dealer or write to the Academy of Model Aeronautics to find an 
experienced instructor in your area.  Write to:  Academy of Model Aeronautics, 5151 Memorial Dr. Muncie, IN  47302 
 

LIMITED WARRANTY 

Lanier R/C is proud of the care and attention that goes into the manufacture of parts for its model kits.  The company 
warrants that for a period of 

3

0 days, it will replace, at the buyers request, any part or material shown to the company’s 

satisfaction to have been defective in workmanship or material at the time of purchase. 
No other warranty of any kind, expressed or implied, is made with respect to the merchandise sold by the company.  The 
buyer acknowledges and understands that he is purchasing only a component kit from which the buyer will himself 
construct a finished flying model airplane.  The company is neither the manufacturer of such a flying model airplane, nor a 
seller of it.  The buyer hereby assumes the risk and all liability for personal or property damage or injury arising out of the 
buyers use of the components or the finished flying model airplane, whenever any such damage or injury shall occur. 
Any action brought forth against the company, based on the breach of the contract of sale to the buyer, or on any alleged 
warranty thereunder, must be brought within one year of the date of such sale, or there after be barred.  This one-year 
limitation is imposed by agreement of the parties as permitted by the laws of the state of Georgia. 

© 2001 Lanier R/C 

Summary of Contents for MARINER 40 MK II ARF















Reviews: