Hachette Agora Bismarck Pack 04 Build Instructions Download Page 1

Page: 1 / 40

Pack 04 | Build Instructions

Your 1:200 scale model of the legendary battleship Bismarck is packed with

intricate details which precisely replicate every aspect of this state-of-the-

art warship. Each piece has been created using premium quality materials to

bring maximum enjoyment during your complete build.

In your fourth model pack, you will assemble:

North America Edition by Agora Models

STAGE 33: MOTOR FOR THE FORWARD

RADAR EQUIPMENT

STAGE 34: RADAR CONTROL CENTRE

STAGE 35: A KEEL SECTION AND

A DISPLAY STAND

STAGE 36: MOTOR FOR THE FORETOP

RADAR INSTALLATION

STAGE 37: THE FORETOP RADAR

AND A PORT HULL SECTION

STAGE 38: THE FORETOP RADAR

AND A STARBOARD HULL SECTION

STAGE 39: THE NEXT HULL SECTION

STAGE 40: FIRE CONTROL POST DETAILS AND

SEARCHLIGHT DECK

STAGE 41: THE NEXT SECTION OF HULL

STAGE 42: THE SIXTH KEEL SECTION

STAGE 43: ADMIRAL’S BRIDGE

STAGE 44: THE UPPER MAST DECK

Summary of Contents for Agora Bismarck Pack 04









































Search results

Summary of Contents for Agora Bismarck Pack 04

Reviews:

Related manuals for Agora Bismarck Pack 04

Brands by name

Popular brands

Hachette Agora Bismarck Pack 04, Build Instructions

Search results

Summary of Contents for Agora Bismarck Pack 04

Reviews:

Related manuals for Agora Bismarck Pack 04

Brands by name

Popular brands