GW Instek COM-804 User Manual Download Page 41

Page: 41 / 157

GOM-804 & GOM-805 User Manual

The

△

% compare function displays the deviation of the

measured value from the reference value as a percentage.

{ [(Measured Value-Reference)/Reference]%}.

Compare function

indicator

Deviation of the

measured value from

the reference value as

a percentage

Measured value

Reference, limits, compare

mode and beep mode

Pass/Fail judgment

The upper (HI) and low (LO) limits are set as a

percentage

from

the reference value. (Identical to the %

compare mode)
A measured value that falls within the upper and lower
limits is considered IN (pass), a value that falls below the

lower limits is considered LO, and a value that falls over
the upper limit is a HI.

Reference

value

Upper

limit

Lower

limit

The % compare mode displays the measured value as a

percentage of the reference value [(Measured
Value/Reference Value)%].
The upper (HI) and low (LO) limits are set as a
percentage

from

the reference value. (Identical to the

△

% compare mode)

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for COM-804






























































































































































Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands

GW Instek COM-804, User Manual

Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands