GW Instek COM-804 User Manual Download Page 67

Page: 67 / 157

GOM-804 & GOM-805 User Manual

PWM Setting

Background

The PWM setting will set the duty of the PWM Drive
setting. The duty is set with ON and OFF times for the

waveform.

OFF time

time

See page 31 for Drive setting details.

1. Select PWM
setting

From one of the main screens, press
the

ESC

key so that the menu

system at the bottom of the display

has focus.
Go to Meas. Setup and press Enter.
Go to PWM and press Enter.

Meas. Setup

menu icon

Move

Select menu

or setting

Enter

2.PWM setting
appears

Use the arrow keys to set the ON and OFF time for the

duty. Press Enter to confirm the setting.

PWM

ON
OFF

03 ~ 99 time units*
0100 ~ 9999 ms

he ON time setting is set in “time units”, not

milliseconds. The amount of time in a time unit depends
on the line frequency settings (see page 67).

Line frequency

1 Time Unit

60Hz

16.6mS

50Hz

20mS

Note

Pressing ESC before pressing ENTER will exit the PWM
setting.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for COM-804






























































































































































Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands

GW Instek COM-804, User Manual

Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands