GW Instek COM-804 User Manual Download Page 46

Page: 46 / 157

MEASUREMENT

Note

For further details on the ABS or

△

% compare modes,

see the description in the Compare section, page 41.

3. Reference
value setting

Although the 8 bins have their own upper and lower
limits, they still share a common reference value.

Use the arrow keys to go to the Reference setting and
press Enter.
Use the left and right arrow keys to select a digit. Use the
up and down arrow keys to edit the value of the selected

digit and the unit. Press Enter to confirm the setting.

Reference

Move

and edit

Select and

confirm

Enter

Range

000.0001~
999.9999(mΩ/Ω/kΩ/MΩ)

4. Upper & lower
limit settings

Use the arrow keys to go to the upper limit of the first
bin and press Enter.

Use the Left and Right arrow keys to select a digit. Use

the Up and Down arrow keys to edit the value of the
selected digit and unit. Press the Enter key to confirm the

setting.

Repeat for the lower setting.

Repeat for the remaining bins.

Upper, lower

reference

Move

and edit

Select and

confirm

Enter

Setting range

ABS mode: 000.0000~999.9999

(mΩ/Ω/kΩ/MΩ)

△

% mode: -999.99 ~ +999.99

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for COM-804






























































































































































Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands

GW Instek COM-804, User Manual

Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands