GW Instek COM-804 User Manual Download Page 74

Page: 74 / 157

MEASUREMENT

Hold example

Hold: The results of the previous tests are held until the

current test has completed.

Previous results

held

New results

Trigger

Ready

EOT

Pass

Fail

High

Low

EOT falling

edge

EOT rising

edge

results

1. Select External
I/O setting

From one of the main screens, press
the

ESC

key so that the menu

system at the bottom of the display

has focus.
Go to System and press Enter.
Go to Utility and press Enter.
Go to External I/O and press

Enter.

System

menu icon

Move

Select menu

or setting

Enter

2. External I/O
menu appears

Use the arrow keys to choose Handler Mode and press

Enter.
Use the arrow keys to set the handler mode. Press Enter

to confirm the setting.

Handler Mode

HOLD, CLEAR

Note

Pressing ESC before pressing ENTER will exit from the
Handler Mode setting.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for COM-804






























































































































































Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands

GW Instek COM-804, User Manual

Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands