GW Instek COM-804 User Manual Download Page 79

Page: 79 / 157

GOM-804 & GOM-805 User Manual

Pin Definitions for the Handler
Interface

As this interface is used for the handler and scan functions, the interface

pinout depends on the function mode. The following pinout is only applicable
when using the Binning or Compare function.

HANDLER / SCAN / EXT I/O

Handler Interface for Binning and Compare Functions

Name

Description

Active
modes

In/
Out

1, 17

Reserved

Trigger

Trigger for a single measurement.

All

3, 14,
18

GND

Ground.

Fail

High when the compare result is

either HI or LO (fail).

Compare Out

High

High when the compare result is

deemed HI.

Compare Out

Pass

High when the compare result is IN
(pass).

Compare Out

EOT

High when the AD conversion has

completed. The DUT is ready to be
changed.

Ext

trigger
mode

Out

VINT

Internal DC V5V.

Out

Bin1

High when the binning sorting result
is within the bin1 setting range.

Binning Out

Bin2

High when the binning sorting result

is within the bin2 setting range.

Binning Out

Bin3

High when the binning sorting result

is within the bin3 setting range.

Binning Out

Bin4

High when the binning sorting result
is within the bin4 setting range.

Binning Out

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for COM-804






























































































































































Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands

GW Instek COM-804, User Manual

Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands