GW Instek COM-804 User Manual Download Page 62

Page: 62 / 157

MEASUREMENT

Trigger Delay

Background

The Trigger Delay setting adds a delay to when an
external trigger signal is recognized. Normally the

external trigger is recognized when there is no contact
bounce in the signal for a fixed length of time, this time

is known as the bounce monitoring window. This ensures
that the external trigger signal is stable before it is

recognized. The Trigger Delay time starts right after the
bounce monitoring window ends.

Start measurement

period

External

Trigger signal

Bounce monitoring

window

Trigger

delay time

Measurement

period

Measurement

process

Contact

bounce

Measurement

delay time

Measurement

time

The Trigger Delay setting is turned off by default.

Note

Pin 2 of the Handler/Scan/Ext I/O interface is used for

external triggering, See page 77 for pinout details.

1. Select Trigger
Delay setting

From one of the main screens, press
the

ESC

key so that the menu

system at the bottom of the display
has focus.
Go to Meas. Setup and press Enter.
Go to Trigger Delay and press

Enter.

Meas. Setup

menu icon

Move

Select menu

or setting

Enter

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for COM-804






























































































































































Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands

GW Instek COM-804, User Manual

Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands