manualshive.com logo in svg

GVC KR632, User Manual, Page: 49 / 56

Share
Download
GVC KR632 User Manual Download Page 49

49

disabled. The IDE setting should be AUTO where the AMIBIOS automatically
determines where the off-board PCI IDE controller adapter card is installed in either
Slot1, Slot2, Slot3, Slot4, or Slot5 of the PCI BUS.
In the AMIBIOS for the Intel 82440LX ISA chipset, this option forces IRQ14 and IRQ
15 to be allocated for PCI slots on the PCI Local Bus. This is necessary to support non
Plug & Play compliant ISA IDE controller adapter cards.

Choose one out of six slots or Auto for setting the following two items.

Offboard PCI IDE Primary IRQ / Offboard PCI IDE Secondary IRQ : 

These

options Specify the PCI interrupt used by the Primary (or Secondary) IDE channel on
the offboard PCI IDE controller.

 

l

 

PCI / Plug and Play Setup > DMA Channel 0

l

 

PCI / Plug and Play Setup > DMA Channel 1

l

 

PCI / Plug and Play Setup > DMA Channel 3

l

 

PCI / Plug and Play Setup > DMA Channel 5

l

 

PCI / Plug and Play Setup > DMA Channel 6

l

 

PCI / Plug and Play Setup > DMA Channel 7

 

These options allow you to specify the bus type used by
each DMA channel.

4. BIOS SETUP

 
 

PnP ( Default )

ISA/EISA

Summary of Contents for KR632

























































Reviews:

No comments