manualshive.com logo in svg

GVC KR632, User Manual, Page: 44 / 56

Share
Download
GVC KR632 User Manual Download Page 44

44

4.2.4 MAIN MENU > POWER MANAGEMENT SETUP

This submenu contains 5 major items. Some item contain several detailed settings
allowing the user to modify the setup if Enabled. The user can set the suspend type,
time and other GREEN Functions in this submenu.

l

 

Power Management Setup > Power Management/APM

 
 

Set this option to Enabled to set the following 17 items:

 
 

Green PC Monitor Power State : 

Enable to support for the Intel Instant ON

specification.

 
 

Video Power Down Mode : 

This option specifies the power state that the video

subsystem enters when AMIBIOS places it in a power saving state after a pre-
specified period of display inactivity has expired. This setting contains Standby,
Suspend and Disabled modes. The default setting is Disabled.

 
 

Hard Disk Power Down Mode : 

This option specifies the power conserving

state that the hard disk drive enters after the pre-specified time period of hard
drive inactivity has expired. This setting contains Disabled, Standby and Suspend
modes. The default setting is Disabled.

4. BIOS SETUP

 
 

Standby Time Out (Minute) : 

This option specifies the length of time the

Move to items

Exit to

Main Menu

Enter

Sub-Menu

Modify values

Figure 5 : POWER MANAGEMENT SETUP

Summary of Contents for KR632

























































Reviews:

No comments