Guilin Woodpecker Medical Instrument Endo Radar Plus Instruction Manual Download Page 5

Page: 5 / 45

Tester Lubricator

USB wire Protective silicon cover

1.4 Indications for use

Endo Radar Plus is a cordless endo motor with root canal

measurement capability. It can be used as a endo motor for preparation

and enlargement of root canals, or device for measuring canal length. It

can be used to enlarge the canals while monitoring the position of the file

tip inside the canal.

1.5 Range of application

1.5.1 The device can be used for preparation and enlargement of root

canals, or device for measuring canal length.

1.5.2 The device must be operated in hospital and clinic by the

qualified dentists.

1.6 Contraindications

In cases where a patient has been fitted with an implanted heart

pacemaker (or other electrical equipment ) and has been cautioned

against the use of small electrical appliances (such as electric shavers ,

hair dryers , etc ) it is recommended not to use the this device.

1.7 Device safety classification

1.7.1 Type of operation mode: Continuous operating device

1.7.2 Type of protection against electric shock: Class II

1.7.3 Base and motor handpiece: internally powered device

1.7.4 Degree of protection against electric shock: B type applied part

1.7.5 Degree of protection against harmful ingress of water: Ordinary

equipment (IPX0)

1.7.6 Degree of safety application in the presence of a flammable

anesthetic mixture with air, oxygen, or nitrous oxide: Equipment cannot

be used in the presence of a flammable anesthetic mixture with air,

Summary of Contents for Endo Radar Plus














































Search results

Summary of Contents for Endo Radar Plus

Reviews:

Related manuals for Endo Radar Plus

Brands by name

Popular brands

Guilin Woodpecker Medical Instrument Endo Radar Plus, Instruction Manual

Search results

Summary of Contents for Endo Radar Plus

Reviews:

Related manuals for Endo Radar Plus

Brands by name

Popular brands