Guilin Woodpecker Medical Instrument Endo Radar Plus Instruction Manual Download Page 39

Page: 39 / 45

Handle with care

Keep dry

Temperature for storage and transport condition

Humidity for storage and transport condition

Atmospheric pressure for for storage and transport condition

Appliance compliance WEEE directive

Authorised Representative in the EUROPEAN

COMMUNITY

12 Statement

All rights of modifying the product are reserved to the manufacturer

without further notice. The pictures are only for reference. The final

interpretation rights belong to GUILIN WOODPECKER MEDICAL

INSTRUMENT CO., LTD. The industrial design, inner structure, etc,

have claimed for several patents by WOODPECKER, any copy or fake

product must undertake legal responsibilities.

13 EMC-Declaration of conformity

The device has been tested and homologated in accordance with EN

60601-1-2 for EMC. This does not guarantee in any way that this device

will not be effected by electromagnetic interference Avoid using the

device in high electromagnetic environment.

Technical Description Concerning Electromagnetic Emission
Table 1: Declaration - electromagnetic emissions

Guidance and manufacturer’s declaration - electromagnetic emissions

The model Endo Radar Plus is intended for use in the electromagnetic

environment specified below. The customer or the user of the model Endo Radar

Plus should assure that it is used in such an environment.
Emissions test

Compliance

Electromagnetic environment -

guidance

Summary of Contents for Endo Radar Plus














































Search results

Summary of Contents for Endo Radar Plus

Reviews:

Related manuals for Endo Radar Plus

Brands by name

Popular brands

Guilin Woodpecker Medical Instrument Endo Radar Plus, Instruction Manual

Search results

Summary of Contents for Endo Radar Plus

Reviews:

Related manuals for Endo Radar Plus

Brands by name

Popular brands