background image

English (GB)

24

Bit 10:
PitPump1PumpDownAck

Bool

Indicates if a PitPump1PumpDown control bit is acknowledged by the 
device. 
This bit is only active if AutoAckControlBits (register 00005, bit 0) is set 
to "0".
0: Not acknowledged
1: Acknowledged.

Bit 11:
PitPump2PumpDownAck

Bool

Indicates if a PitPump2PumpDown control bit is acknowledged by the 
device. 
This bit is only active if AutoAckControlBits (register 00005, bit 0) is set 
to "0".
0: Not acknowledged
1: Acknowledged.

Bit 12:
PitPump3PumpDownAck

Bool

Indicates if a PitPump3PumpDown control bit is acknowledged by the 
device. 
This bit is only active if AutoAckControlBits (register 00005, bit 0) is set 
to "0".
0: Not acknowledged
1: Acknowledged.

Bit 13:
PitPump4PumpDownAck

Bool

Indicates if a PitPump4PumpDown control bit is acknowledged by the 
device. 
This bit is only active if AutoAckControlBits (register 00005, bit 0) is set 
to "0".
0: Not acknowledged
1: Acknowledged.

00202

Bit 0:
AlarmInPumpOrPit

Bool

Main status of warning(s).
0: No active warnings.
1: One or more active warnings.

Bit 1:
WarningInPumpOrPit

Bool

Main status of alarm(s).
0: No active alarms.
1: One or more active alarms.

Bit 2:
ManualControlStatus

Bool

Main status of manual pump control.
0: No manual pump control enabled (full "Auto")
1: Manual pump control enabled (partly or completely).

Bit 3: RESERVED

-

-

00203

PitMode

Enum

Pit mode.
0: Single-pit mode
1: Multi-pit mode.
See section 

10.4 Single-pit and multi-pit mode

.

00204

SinglePitStopLevel

0.01 m

Stop level, pit. Used in single-pit mode only. 
Pit mode: 0. Pit mode is set in register 00203.

00205

SinglePitStartLevelMax

0.01 m

Start level max., pit. Used in single-pit mode only. 
Pit mode: 0. Pit mode is set in register 00203.

00206

SinglePitStartLevelBand

0.01 m

Start level band, pit. Used in single-pit mode only. 
Pit mode: 0. Pit mode is set in register 00203.

00207

SinglePitHighWaterLevel

0.01 m

High water level, pit. Used in single-pit mode only. 
Pit mode: 0. Pit mode is set in register 00203.

00208

MultiPitPump1StopLevel

0.01 m

Stop level, pump 1. Used in multi-pit mode only. 
Pit mode: 1. Pit mode is set in register 00203.

00209

MultiPitPump1StartLevelMax

0.01 m

Start level max., pump 1. Used in multi-pit mode only. 
Pit mode: 1. Pit mode is set in register 00203.

00210

MultiPitPump1StartLevelBand

0.01 m

Start level band, pump 1. Used in multi-pit mode only. 
Pit mode: 1. Pit mode is set in register 00203.

00211

MultiPitPump1HighWaterLevel

0.01 m

Actual high water level, pump 1. Used in multi-pit mode only. 
Pit mode: 1. Pit mode is set in register 00203.

00212

MultiPitPump2StopLevel

0.01 m

Stop level, pump 2. Used in multi-pit mode only. 
Pit mode: 1. Pit mode is set in register 00203.

00213

MultiPitPump2StartLevelMax

0.01 m

Start level max., pump 2. Used in multi-pit mode only. 
Pit mode: 1. Pit mode is set in register 00203.

00214

MultiPitPump2StartLevelBand

0.01 m

Start level band, pump 2. Used in multi-pit mode only. 
Pit mode: 1. Pit mode is set in register 00203.

00215

MultiPitPump2HighWaterLevel

0.01 m

High water level, pump 2. Used in multi-pit mode only. 
Pit mode: 1. Pit mode is set in register 00203.

00216

MultiPitPump3StopLevel

0.01 m

Stop level, pump 3. Used in multi-pit mode only. 
Pit mode: 1. Pit mode is set in register 00203.

00217

MultiPitPump3StartLevelMax

0.01 m

Start level max., pump 3. Used in multi-pit mode only. 
Pit mode: 1. Pit mode is set in register 00203.

00218

MultiPitPump3StartLevelBand

0.01 m

Start level band, pump 3. Used in multi-pit mode only. 
Pit mode: 1. Pit mode is set in register 00203.

Address

Register name

Scale

Description

Summary of Contents for CIU 202





























































Reviews: