GREAT PLAINS 3S-3000-3210 Operator'S Manual Download Page 31 | Manualshive

Page: 31 / 118

background image

3S-3000/F/HD/HDF

Table of Contents

Operating Instructions

27

2018-06-18

Table of Contents

195-441M

Transport Lift

1.

Fold the drill (unless this lift is for maintenance or
adjustment). See “

” on page 25.

2.

If the Two Outlet conversion kit is installed, a selector
valve near the hitch must be operated to switch
between Transport Lift and Opener Lift. See “

Selector Valve Operation

” on page 42.

3.

Supply oil to the base (extend) ends of the Transport
Lift cylinders.

Refer to Figure 17

4.

Leave the circuit extended until mainframe lift is
complete, the transport hooks have engaged, the
wing ends are lifted off the ground, and the front box
lift cylinder is fully extended.

Refer to Figure 18

5.

Swing the locks up and onto the transport lift
cylinders. They are temporarily held in place with
polymer bumpers. They are firmly held in place when
the cylinder is relaxed in step 7.

6.

Rotate cylinder lock channel over rod on front box lift
cylinder.



NOTE:

Bumpers hold the transport lift cylinder lock channels
in place temporarily. The channels will remain in
position when cylinders settle against channels.

7.

Slowly reverse the Transport Lift circuit lever until all
three lock channels are resting firmly on the rod ends
of the transport lift and box lift cylinders. Set circuit
lever to off.

The drill is now ready for the pre-transport checklist. See
“

” on page 28.

Figure 18 - Fold

Transport Lift Cylinder Lock

15552

«
...
29
30
31
32
33
...
»

Summary of Contents for 3S-3000-3210























































































































Reviews:

No comments

Related manuals for 3S-3000-3210

Brand: ESD Pages: 6

Origo Feed 354 P3

Brand: ESAB Pages: 62

Streamfeeder V-710IJ

Brand: Barry-Wehmiller Pages: 58

Brand: Aim Pages: 35

Brand: Migatronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands