GREAT PLAINS 3S-3000-3210 Operator'S Manual Download | Manualshive

Page: 25 / 118

background image

3S-3000/F/HD/HDF

Table of Contents

Preparation and Setup

21

2018-06-18

Table of Contents

195-441M

Setting the Bypass Valve

Refer to Figure 11

A bypass valve

is plumbed into the opener down

pressure circuit. Tractors with load-sensing,
closed-center hydraulics require this bypass valve to
protect the tractor hydraulic system.

If you are unsure what type of hydraulic system is on
your tractor, contact your tractor manufacturer.

Turn the locking disc

counter-clockwise to enable

adjustment.

Turn the adjustment knob

counter-clockwise to

increase flow.

Turn the adjustment knob

clockwise to decrease flow.

Turning it fully clockwise stops all bypass flow.

Tractors with Open Center Hydraulics

Release locking disc. Close bypass valve for no oil flow
by turning knob on valve clockwise completely. Tighten
locking disc. Always operate the drill with the bypass
valve locked closed.

Tractors with Pressure Compensating
Closed Center Hydraulics (PC Closed)

Release locking disc. Close bypass valve for no oil flow
by turning knob clockwise completely. Tighten locking
disc. Always operate the drill with the bypass valve
locked closed.

Tractors with Load Sensing Closed Center
Hydraulics (LS Closed) or Pressure Flow
Compensating (PFC) Systems

Machine Damage Risk

: Failure to use the bypass valve on

load-sensing tractors may cause major tractor damage.

1.

Release locking disc. Initially close bypass valve for
no oil flow by turning knob on valve clockwise
completely.

2.

With tractor at half throttle, adjust flow-control valve
on tractor so openers raise and lower at a
reasonable speed. Keep tractor at one-half throttle
for remaining steps.



NOTE:

The faster openers raise and lower, the greater
potential for oil heating, premature wear or tractor
damage.

3.

Engage tractor hydraulics and lower openers. Lock
hydraulic lever on tractor for continuous operation.
See “

Raising and Lowering Openers

” on page 24.

Figure 11

Bypass Valve

19045

1

2

3

«
...
23
24
25
26
27
...
»

Summary of Contents for 3S-3000-3210























































































































Reviews:

No comments

Related manuals for 3S-3000-3210

Brand: Robe Pages: 50

Brillion Turfmaker III Series

Brand: Landoll Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands