GREAT PLAINS 3S-3000-3210 Operator'S Manual Download | Manualshive

Page: 9 / 118

background image

3S-3000/F/HD/HDF

Table of Contents

Important Safety Information

5

2018-06-18

Table of Contents

195-441M

Tire Safety

Tire changing can be dangerous and should be
performed by trained personnel using correct tools and
equipment.



When inflating tires, use a clip-on chuck and extension
hose long enough for you to stand to one side–not in front
of or over tire assembly. Use a safety cage if available.



When removing and installing wheels, use wheel-handling
equipment adequate for weight involved.

Safety At All Times

Thoroughly read and understand the instructions in this
manual before operation. Read all instructions noted on
the safety decals.



Be familiar with all drill functions.



Operate machinery from the driver’s seat only.



Do not leave drill unattended with tractor engine running.



Do not dismount a moving tractor. Dismounting a moving
tractor could cause serious injury or death.



Do not stand between the tractor and drill during
hitching.



Keep hands, feet and clothing away from power-driven
parts.



Wear snug-fitting clothing to avoid entanglement with
moving parts.



Watch out for wires, trees, etc., when folding and raising
drill. Make sure all persons are clear of working area.



Do not turn tractor too tightly, causing drill to ride up on
wheels. This could cause personal injury or equipment
damage. Important Safety Information(topics)

«
...
7
8
9
10
11
...
»

Summary of Contents for 3S-3000-3210























































































































Reviews:

No comments

Related manuals for 3S-3000-3210

Brand: FONRI Pages: 96

Brand: Terradonis Pages: 12

Brand: Terradonis Pages: 10

Brand: Vaderstad Pages: 122

Brand: EarthWay Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands